ATEC

Products
+
  • 10.png
  • 21.png
  • 23.png
  • 24.png
  • 150立方高低温.png

Walk in vehicle test cabin

It is used to test the heat and cold resistance of national defense industry, aerospace industry, automation components, automobiles and components, electronic and electrical parts, and related products in plastic

Temperature Range::

Optional range: low temperature - 20 (- 40 ℃, - 60 ℃) ~ high temperature + 85 ℃ (+ 85 ℃, + 120 ℃, + 150 ℃)

Cooling Rate:

The optional range is 0.5 ~ 15 ℃ / min, and the load can be specified

Details

It is used to test the heat and cold resistance of national defense industry, aerospace industry, automation components, automobiles and components, electronic and electrical parts, and related products in plastic, chemical and pharmaceutical industries. It is suitable for testing test parts and products with large quantity and volume. ATEC provides customers with a comprehensive environmental reliability test scheme. At present, 3168m3 vehicle test chamber has been successfully developed and delivered.

Temperature range: - 70 ℃ ~ 150 ℃, humidity range: 20% ~ 98% RH; Cooling rate: 1 ~ 20 ℃ / min

Technical parameter

Model

UC8-6085

UC12-6085

UC20-6085 UC30-6085 UC40-6085
Nominal internal volume (M3) 8M3 12M3 20M3 30M3 40M3
Performance
Temperature range Optional range: low temperature - 20 (- 40 ℃, - 60 ℃) ~ high temperature + 85 ℃ (+ 85 ℃, + 120 ℃, + 150 ℃)
Humidity range (ONLY UC series) 20%~98%R.H(Humidity operating range+20℃~ +85℃)
Temperature fluctuation ±0.3℃
Temperature deviation ±2℃
Humidity deviation (UC series only) -3~+2%R.H (75% R.H.以上), ±5%R.H (75% R.H以下)
Temperature rise and fall rate (whole process average) The optional range is 0.5 ~ 15 ℃ / min, and the load can be specified
Note The above indexes are measured under no-load and ambient temperature of 20 ± 2 ℃, in which the temperature rise and fall rate is measured at + 85 / - 55 ℃
Internal dimensions(mm)
D 2000 3000 4000 4000 5000
W 2000 2000 2500 3000 3200
H 2000 2000 2000 2500 2500
External dimension of box(mm)
D 3000 3000 5000 5000 6000
W 2240 2240 2740 2740 2940
H 2320 2320 2320 2820 2820
Note Unit dimensions are not included above
Observation window 400×500With heating device to prevent condensation and frosting
Test hole 2Ø100
Lighting Equipped with lighting lamp
Operating ambient temperature

5~35℃

Cooling mode Water cooling (water temperature 7 ~ 28 ℃, water pressure 0.2 ~ 0.4MPa)
Power Supply 380V±10%/50HZ±1,Three phase five wire system(3P+N+G)
Meet the test method

GB2423.1、GB2423.2、GB2423.3、GB2423.4、GJB150.3、GJB150.4、GJB150.9 、

GB11158、GB10589、MIL-STD-810F method501.2,502.2

Safety protection measures Power supply undervoltage, overvoltage, phase loss and phase sequence error protection; Triple overtemperature protection; Heater short circuit protection; Refrigerator overpressure / overload protection; Water shortage protection; Overload / overheating protection of blower motor; Control board overcurrent protection; Leakage protection; Humidification fault protection.
Optional Special test hole, slope, timing function, temperature rise and fall rate customization, Internet function, etc.

 

Previous

Next

Previous

Next

Other Products

Multi axis rotation test chamber

Temperature range:

-55 ℃ 100 ℃

Cooling rate:

Thermal vacuum test chamber

Temperature range:

Cooling rate:

Compound salt spray test chamber

Temperature range:

-20 ℃ ~ 60 ℃ controllable

Cooling rate:

Rain test chamber

Temperature range:

Cooling rate:

Sand and dust test chamber

Temperature range:

Cooling rate:

New energy test chamber

Lithium battery and fuel cell

Temperature range:

-50 ℃ ~ 120 ℃

Cooling rate:

1~5 ℃/min (optional)

I want to consult

Submission